Factory fire safety management system

(1) Establish a step-by-step fire safety responsibility system and post fire safety responsibility system, clarify their respective responsibilities, and implement a patrol inspection system.

(II) During the inspection, a hidden danger of fire was discovered. The inspectors should fill in the records and in accordance with regulations, require the relevant personnel to sign the records.

(3) The inspection department shall notify the inspection department in writing of the inspection status. The person in charge of the inspection department shall promptly rectify the fire hazard according to the notice requirements.

(4) If the hidden dangers of the fire discovered during the inspection are not rectified in time according to the stipulated time, a penalty shall be imposed according to the provisions of the company.

2

(1) The width of the safety exit doors, evacuation stairs, and evacuation walkways of workshops, warehouses and dormitories in the factory must be set according to the specifications.

(b) All evacuation exits, stairs and aisles must be equipped with appropriate emergency lighting and evacuation signs.

(3) During work, production workshops and warehouses shall ensure that safety exits are unimpeded and safety exits may not be locked.

(D), workshops, warehouses should be stored according to regulations, may not block the channel.

(5) The person in charge of each department shall regularly check whether the evacuation signs and emergency lighting facilities are in good condition and find damages and repair in time.

3

(1) On-duty personnel should perform their duties with due diligence. If there is a fire accident, they should be dealt with promptly according to relevant plans and report to relevant departments.

(2) On-duty personnel should record the status of shifts on duty and do a good job in transition work.

(3) On-duty personnel should observe the automatic fire alarm system and automatic fire extinguishing system self-checking daily and find that the fault should be eliminated in time to ensure the normal operation of the system.

4

(1) The company shall strictly implement fire safety regulations for the use of electricity by fire.

(B), electricity safety management: 1 It is strictly prohibited to set up wires at will, and it is forbidden to overload power. 2. After the workshops are off duty, the power off should be turned off, otherwise the safety department will impose sanctions on the responsible persons. 3 , prohibit the private use of electric hot rods, electric stoves and other high-power electrical appliances.

(III) Fire safety management:

1. Strictly enforce the approval system for hot work, and remove flammable and explosive dangerous goods within a range of 4 meters in the vicinity of the hot spot prior to hot work or make proper safety isolation, and prepare appropriate types and quantities of fire-fighting equipment to be used at any time After finishing the work, it should be replaced immediately.

2. In the case of hot work in situ at the operation site, an overheated operation that should be more than 2 meters above the ground must ensure that one person is fully responsible for extinguishing sparks that may ignite other materials at any time below.

5

(1) Inflammable and explosive dangerous goods shall have dedicated warehouses equipped with necessary fire-fighting equipment and facilities.

(II) Inflammable and explosive dangerous goods shall be classified and stored separately. Inflammable and explosive chemicals that have different chemical properties or fire extinguishing methods should be stored separately.

(3) Inflammable and explosive dangerous goods shall be inspected by the inspection department before being put into the warehouse, and the entry and exit shall be registered.

(4) Inventory items should be classified and stored in separate storage. Each floor area should not be larger than 100 square meters, and the distance between concrete and concrete should not be less than one meter. The distance between the concrete wall and the wall should be no less than 0.5 meters. The spacing between the columns is not less than 0.3m and the width of the main channel is not less than 2m.

(5) Access to flammable and explosive dangerous goods shall be carried out in accordance with the rules of safe operation, and non-workers shall enter the premises at will.

(6) Inflammable and explosive places shall take fire prevention and explosion prevention measures in accordance with the requirements of fire protection regulations and do maintenance work for fire prevention and explosion protection facilities.

6

(1) Personnel in charge of duty before work should check the water and electricity in a timely manner to ensure that all power sources are cut off before leaving.

(B), electrical equipment and lines to be regularly overhauled, found that the problem was reported in a timely manner and dealt with in a timely manner.

(3) Storehouses that store gas shall adopt fire prevention, explosion-proof, and anti-static measures in strict accordance with the requirements of the fire protection regulations.

(4) Fire-fighting facilities and fire-fighting equipment shall be stored at fixed points, fixed and maintained, and regularly checked, and the records of inspections shall be recorded.

7

(1) No smoking is allowed in the workshop and unauthorized open fire operations are conducted.

(b) Do not occupy evacuation routes.

(3) Do not install barriers such as barriers that affect evacuation on safety exits or evacuation routes.

(4) It is forbidden to lock or close the safety exit door during production work.

(e) No casual use of fire-fighting equipment is permitted.

(6) Non-mechanic personnel are not allowed to disassemble and disassemble the equipment.

(7) No unauthorized operation of dangerous machines is allowed.

(8) Failure to use the equipment before it is repaired.

(9) It is forbidden to work, cause trouble, fight or absent from duty during work hours.

(10) Do not allow barefoot to enter the workshop. Children are not allowed to enter the workshop.

The information in this article comes from the Internet and was reorganized and edited by China Rescue Equipment Network.