Nowadays, many people are cold at home, and they are doing some insulation outside the house to bring warmth to the house. But when you keep the outer wall warm, do you know what construction points are there? Understand? Next, the decoration house Xiaobian introduces the main points of exterior wall insulation construction and the selection of exterior wall insulation materials. I hope everyone can refer to the exterior wall for warmth. I. Main points of exterior wall insulation construction 1. The construction points of the polystyrene board are attached. Paste the lapped net: Paste the lapped net in the following parts and seal and waterproof. Around the door and window openings, reserved openings, parapet walls, feet, balconies, canopies, etc., deformation joints and different layers of different materials in the base layer. The above parts are called system terminals. The overturned mesh cloth is required to be pressed into the polystyrene board to have not less than 100 mm on both sides. 2. Paste the polystyrene board by point frame method: uniformly spread the mixed slurry around the polystyrene board with a trowel, uniformly apply some gray cakes in the blank place, and then align the polystyrene board according to the predetermined position. And evenly press hard to detect the verticality and flatness at any time, so that the polystyrene board and the substrate are firmly bonded and flat. After flattening, the width of the slurry around the polystyrene board is about 60 mm, the narrowest part is not less than 60 mm, the diameter of the gray cake is not less than 100 mm, the thickness is 5 mm, and the bonding area is not less than 30% of the area of ​​the polystyrene board. 3. Protective layer construction requirements. The mixed mortar was evenly coated on the surface of the polystyrene board with a trowel. Press the pre-cut grid cloth to the positive position with a file into the plaster, and press it line by line to avoid wrinkles. The grid cloth is laid horizontally and laid down from top to bottom, and then laid along the corners of the outer wall. When the door and window openings are opened, a 45° diagonal grid cloth with a length of 300mm and a width of 200mm is attached to the corners of the hole. A reinforced mesh shall be laid at the following locations: the bottom layer is 2 m above the outdoor ground; it may be subjected to impact. Strengthen the method of paving the mesh cloth: first attach the reinforcing net, then stick the standard net, and add a layer of plastering mortar between the reinforcing net and the standard net. 4. Meshing of the mesh cloth: the overlapping width of the standard mesh cloth is ≥100mm; the reinforcing mesh cloth shall not be overlapped and bent, and the mesh edge shall be butted. The mesh cloth at the corner should be laid continuously, and the package rotation width is ≥200mm. The treatment of the joint: a mesh with a lap width of ≥100 mm is reserved for the working surface which cannot be continuously constructed, and the mesh cloth is kept smooth and clean for subsequent construction. Smoothing and trimming: use a trowel to smooth the mortar 5. Precautions. First, each compartment unit must be completed in one time. It is forbidden to appear in a compartment. Secondly, when it is close to the edge of the grid, it should be treated finely. Do not apply the new mortar to the adjacent plates. When grinding, avoid secondary grinding of the finished plates. The third horizontal split seam position is not less than 0.3 m per step of the scaffold height. The fourth construction wall shall be protected from sun and wind. Avoid rainwater scouring within 24 hours after the final construction. 2. Selection of exterior wall insulation materials 1. Thermal conductivity, thermal conductivity is the thermal conductivity. The property of the heat transfer material to transfer heat is called thermal conductivity. It is a parameter of the ability of the thermal insulation material to transfer heat, reflecting the thermal conductivity of the material, and is the main thermophysical property of the thermal insulation material. Thermal conductivity is closely related to other physical properties of the material, such as density and moisture content, and is related to the internal structure of the material and to the size of the insulation layer. 2. Bulk density, the thermal insulation material that is dried and in a loose state at a temperature of 110 ° C, the mass per unit volume is the bulk density of the material. It has the problem of an optimum bulk density value, that is, it has a small thermal conductivity and a good thermal insulation effect under the optimum bulk density. In order to save energy and reduce the structural load of the insulated pipe and hanger structure in the project, insulation materials with small bulk density should be used as much as possible. Generally, the bulk density of soft and semi-rigid materials shall not exceed 150kg/m3, and the bulk density of hard materials shall not exceed 220kg/m3. 3. The maximum use temperature, the maximum use temperature refers to the limit temperature that the insulation material can withstand for a long time safe and reliable operation. The use temperature of general insulation materials refers to the long-term use of insulation materials at this temperature, and its physical and chemical properties are stable, in line with the technical requirements of design and operation. A lot of people in the real life, a lot of people will keep the outer wall warm, the above article is about the external wall insulation construction points and the choice of external wall insulation materials, Xiaobian said that it is not clear If you want to know more about the decoration, please continue to pay attention to the decoration home network. More related wonderful reading: What are the construction specifications for exterior wall insulation? What are the external wall insulation materials? External wall insulation materials require external wall insulation materials prices Building exterior wall insulation material how to install external wall insulation material What are the polyurethane exterior wall insulation? Polyurethane product features Introduction of external wall insulation nails, introduction of exterior wall insulation materials External wall insulation decoration integrated board purchase insulation decoration integrated board advantages
The flush plate is an essential component of a concealed installation system that remains visible to the user. Fabia, a brand that pays great attention to design elements and reliable functionality, offers a range of flush plates with different designs, materials, colors, and finishes. These flush plates not only serve as switches for flushing but also provide access to the hidden water tank for maintenance purposes. Flush Plate, Toilet Push Button, Toilet Button Panel, Flush Button, Toilet Flush Panel Guangdong Fabia Intelligent Technology Co., Ltd , https://www.nbsmartfabiatoilet.com
Fabia manufactures flush plates primarily using three materials: ABS plastic, stainless steel, and glass. Each material offers unique aesthetic and functional characteristics to complement the overall bathroom design. The choice of material depends on the customer's preference and the desired visual appeal.
In terms of functionality, flush plates can be categorized into three types: mechanical (manual pressing), pneumatic, and sensor-based. Mechanical flush plates require manual pressing to initiate the flushing process, providing a traditional and tactile experience. Pneumatic flush plates utilize air pressure to trigger the flushing mechanism, offering a touchless operation. Sensor flush plates use advanced technology to detect the user's presence and automatically activate the flushing system, providing a convenient and hygienic solution.
The majority of flush plates available on the market are dual flush panels, which allow users to choose between two flush volumes based on water consumption. Typically, a short flush consumes around 3 liters of water, while a long flush utilizes 4.5 to 6 liters. The dual flush button design is the most common type of flush plate, ensuring both economic and environmental savings by promoting water conservation.
In a word, Fabia's flush plates are designed to combine functional efficiency with aesthetic appeal. By offering a variety of materials, designs, and functional options, Fabia enables customers to select the flush plate that best suits their needs and preferences while promoting water-saving practices and enhancing the overall bathroom experience.