After the wooden door has been used for a long time, there will definitely be more or less damage. It would be a pity to throw it away. At this time, you need to renovate the wooden door. What should I pay attention to when renovating wooden doors? How to renovate is the most cost-effective? If the surface of the wooden door is damaged, such as cracks or broken pits in some places, you should first put the putty on the damaged place, then sand the sandpaper, then brush the primer and topcoat. If the base layer is not damaged, consider painting directly. The correct way to do this is to polish the original wooden door with sandpaper and then apply the primer and topcoat directly. Because the finished door is waxed on the surface, there will be grease on the surface. After polishing it, it can improve the adhesion of the paint. There is no difference in quality between refurbishment and first-time painting, so don't worry about shorter life or other quality problems. One of the issues that everyone will pay attention to about the renovation of wooden doors is that the original use of oil-based paints or water-based paints on wooden doors will result in poor quality if they are not used in the refurbishment. Experts say that this issue is not a concern. In general, there are three types of oil paints, polyester paint, nitrocellulose paint and alkyd paint. Alkyd paint is an earlier product that works slowly and is used less and less in decoration. The nitro paint dries quickly but the paint film is thin, it needs to be brushed many times, and the humidity is easy to whiten. Polyester paint is used relatively more, film formation is fast and the effect is better. If you are using an oil paint, consider using the same paint or water-based paint. In general, the adhesion of the same paint will be relatively good, with the exception of polyester paint. If you originally brushed the polyester paint and then brushed the polyester paint, you need to melt the original paint film to have a good adhesion. One problem with this refurbishment is that the adhesion between the refurbished paint film and the original paint film is not so good. If the new film is damaged, such as being cut open by a sharp weapon or pulling out a pit, going along the crack or pit will cause the two layers to peel off. The water-based paint is relatively more environmentally friendly, and the wooden door renovation is mostly carried out indoors. The oily paint has a large smell and is difficult to volatilize. It is recommended that everyone use the water-based paint to renovate. It should be noted that if the wooden door is refurbished, the first time the paint is sprayed, the better. Because the original substrate has been dried out during refurbishment, it does not affect the repainted film. If it is a wooden door that has just been bought, it is recommended not to spray it first. Because if the smell is large, it means that it does not dry out, resulting in poor adhesion of the paint film. Since any substrate and material can be refurbished, Ms. Tian wants to change colors naturally. In the lacquer store, Ms. Tian can choose the color she wants according to the color card. However, it should be noted that if the original oil is used and the color is dark, it cannot be covered with a light paint unless the original color is covered with a darker color. If it is originally mixed, there is no limit on the color, and you can change it to any color. For the effect after film formation, the quality and construction of the paint will have a certain impact. Oily paint is generally good, normal construction can be. Usually in the construction of water-based paint, workers are prone to the following mistakes, affecting the construction effect. 1. The water is not properly watered according to the instructions. The water content exceeds the reasonable ratio and affects the film formation effect. 2. Generally speaking, the spray paint brush can be used for three times of primer, but each time it takes 4-6 hours to brush the second coat. The worker brushes the paint a second time every 1-2 hours. The paint film did not dry out, affecting the final result. 3. During construction, the workers will use coarse sandpaper for the sake of the map, but they should use fine sandpaper to polish more finely and the adhesion of the paint film is better. Experts also suggest that since the wooden door renovation is mostly carried out indoors, it is better to remove the door and put it in a special room for better spraying. There is no dust to reduce environmental pollution; secondly, the front and back of the door can be seen very clearly. If it is sprayed directly on the door, it will easily generate fog when spraying, which will affect the line of sight and affect the spraying effect.
AGLEX LED grow lights are with samsung leds and add other bands of lights to ensure well performance.
G series (Linear LED Grow Light design): 110W 220W available, with samsung LM301B 3500K 6500K and red 660nm
K series (Quantum board LED Grow Light design, dimmable. K360 is foldable): 90W 180W 360W available, with samsung lm301b, SMD 3030 3500K 6500K and 660nm
L series (LED Grow Light Bar design, dimmable and foldable): 700W available, with samsung lm301b, SMD 3030 3000K 5000K and 660nm 740nm
M series (LED Grow Light Bar design, dimmable and foldable, external driver): 240w 320w 400w 600W available, with samsung lm301b, SMD 3030 3000K 5000K and 660nm 740nm
Application:
Samsung LED Grow Light Light, LED Grow Light LM301B, Samsung LM301B Grow Light, LED Grow Light Samsung Shenzhen Ameri Technology Co., Ltd. , https://www.aglexz.com
Suit for marijuana, tomatoes, vegetable, strawberry, pepper, microgreen and herbal plants etc. And suit for all the growing stage.
For grow tent, greenhouse, vertical farming, commercial led grow lighting etc.
