How to install the fingerprint access control system? Fingerprint access control installation method. Fingerprint access control refers to the use of human fingerprint recognition to unlock the access control system. It is widely used because of its efficient, convenient, and safe operation features. Fingerprint access control system uses the fingerprint access control device as the unlocking device. The user only needs to tap the finger to realize the unlocking recognition process. The operation is very simple, but there are many things to pay attention to when installing a fingerprint access control system. It is necessary to master the essentials of the procedure. The hardware of the fingerprint access control system is mainly composed of a microprocessor, a fingerprint identification module, a liquid crystal display module, a keyboard, a real-time clock/calendar chip, an electronically controlled lock, and a power supply. The microprocessor serves as the host computer of the system and controls the entire system. The fingerprint identification module mainly completes the functions of fingerprint feature collection, comparison, storage, and deletion. The liquid crystal display module is used to display open-door recordings, real-time clocks, and operation prompts, and forms a human-machine interface with the keyboard. Fingerprint access control, access control, access control power supply, access control switch and other equipment are ready before installation of fingerprint access control. The installation of electric locks is divided into electric plug locks and magnetic locks. Since these two types of locks are currently installed at the most, we will introduce the two types of locks separately. 1, electric plug lock installation, there are two parts, the lock body and iron (lower clip). For frameless glass doors, first fix the lower clamp on the glass door, and the middle line of the door and the distance of 10 cm. Use a square to locate the center point of the jack on the lower clip and mark it on the door frame. Then the lock cylinder's lock core is aligned with the center point just drawn. You can use the auxiliary line to find the center point and draw the square hole size that the lock body will dig. After setting the thread, the square hole can be cut with a cutter. 2, magnetic lock installation, relatively simple, the lock body and the magnet piece together, in the door fixed installation position, draw a good line, the lock body and the top of the fixed separation of the screw hole, after the hand The drill drilled with a 6-centimeter twist drill can be tested by hitting two diagonal holes first. The magnets on the door are in good contact with no gaps. Hit all remaining holes. Fingerprint access control machine, open the door button installation, first use the bracket to draw a hole on the wall, use the impact drill hole, hit the rubber plug, the fingerprint access bracket is fixed, the bottom of the push button button is fixed, go out The button is pressed inside the door. 3, line, from the fingerprint machine to the control box to have a network cable to the network room, a six-wire to the power control box, from the electric lock to the power control box to have a two-wire, two locks, then cloth two (If you want the magnetic detection function to install four-wire); from the door open button to the power control box to be placed in a two-wire, the middle to go the open line to go trunking. 4, wiring, welding, install the software on the computer to set the IP address of the fingerprint machine, add the fingerprint machine number, and then in the monitoring interface you can see the door status icon, if it is displayed in green, it is online, if it is red It is disconnected. Please check whether the crystal head is fully connected. The middle network cable is not damaged. 5, set the fingerprint access control system, follow the steps to enter the fingerprint, set the unlock permission, create a database, the detailed operation, see the fingerprint access control product manual. After installation, check again before turning on the power and check whether the circuit is connected incorrectly. The end of the thread should be covered with tape and sleeve, and it must not be exposed. It may cause short-circuit burnout of the machine. The above is a smart lock China Network Xiaobian published fingerprint access control system installation method tutorial, more fingerprint access control installation problems please refer to this site article description.
Alumina substrate is mainly made of 95%, 99% or 99.5% aluminum oxide ceramics , that work as a functional ceramic component in lots of electrical appliances because of its super insulation, excellent thermal properties.
We focus on tape casting, pressing to manufacturing diveristy of Alumina Ceramic substate, also different shape is available to supply via laser cutting. We are offer to provide many different standard thickness, such as 0.25mm, 0.30mm, 0.40mm and so on are optional to meet customers' specific demand.
In the meantime, we support customize thickness, shape and size. OEM, ODM is welcome.
Ceramic Substrate,Alumina Ceramic Substrate,Insulation Alumina Ceramic Substrates,Small Alumina Ceramic Substrates Jinghui Industry Ltd. , https://www.ceramictek.com
