Today's decoration home Xiaobian brings you the relevant content of the home improvement bathroom tiles . In the renovation of our new home, we should not only pay attention to the living room and bedroom, but also pay attention to the bathroom. Of course, home improvement bathroom tiles have always been a topic of constant discussion. Because of the long-term dampness and immersion in water, the bathroom is more special for other functional spaces. The following small series will introduce you to the home improvement bathroom tile: First, the matching of home decoration bathroom tiles 1. The bathroom is in a damp state for a long time, the floor tiles must ensure non-slip and waterproof, so the bathroom floor tiles are generally made of whole body bricks, and the anti-slip wear resistance of the whole body bricks is good; 2. Bathroom wall tiles generally use glazed tiles, glazed tiles are rich in color patterns and strong anti-fouling ability. 3. The decorative materials of the bathroom wall are glazed tiles, vitrified tiles and mosaics. Nowadays, the most common type of glazed tiles in the family is 300×400mm, 300×300mm and 250×330mm. The specifications of wall tiles are generally determined by the actual size of the space. 4. Commonly used specifications on the ground are 300×300mm and 330×330mm. The bathroom space is usually between 2m2 and 4m2. Even if the bathroom space is large, do not use large-sized floor tiles. Because the bathroom space is relatively small, the corners are too large, the tile cutting frequency is too high, the waste is large, and the floor drain is inconvenient. It is inconvenient to level the floor and cause waste. Light bricks can be used for the choice of wall tiles, or matt tiles can be used. 5. There are also differences between the wall tiles and the floor tiles of the bathroom tiles. The wall tiles must be covered with tiles that are waterproof and resistant to corrosion and mildew (or glass tiles); the tiles of the floor tiles are preferably raised with raised patterns. Because of its strong anti-slip function. Second, the laying of home decoration bathroom tiles 1. In the preparation for renovation, more or less will involve the renovation of the wall. The workers need to finish the construction of the powder in the early stage of the renovation to ensure that the renovation wall can be fully dry. 2, can choose different materials to paste according to the actual economic situation 3. Ingredients Add fresh water to the powdered binder in batches, mixing 1 part water + 3~3.5 parts binder. 4. Stir and adjust the binder slurry until it is evenly lubricated. There is no obvious block or paste. After the mixing, the slurry is allowed to stand for 5-10 minutes, then stirred for 1-2 minutes. . 5, should clean all kinds of dirt on the wall, clean the scene, especially the feet fall. 6. Grab the wall with a trowel and then level it with cement slurry. This process is very important to ensure that the foundation is flat and prevents the drum from sticking. 7, the wall should be painted with waterproof coating to prevent water immersion after the paste, the general height is not less than 1.8 meters, the brush will be slightly higher. 8. According to the requirements of designing the paving pattern, determine the brick-laying scheme and use the ink cartridge to reduce the construction loss. 9. Scrap the just-mixed binder slurry evenly onto the wall. 10. Pulling the groove with a serrated boring tool is a point that distinguishes the old process with the new technology. The adhesive slurry is applied to the surface of the base layer to be laid, and the strip slurry after combing through the serrated boring tool is full and continuous. Intermittent. 11. The tile wall will be laid flat on the base layer of the binder slurry through the pre-cleaned tile, and the tile will be flattened with a rubber hammer. During the construction process, the tile can be rotated in a small amount to make the slurry fully in contact with the back of the tile. Experts recommend that the tiles that have been laid on the base layer be randomly removed for inspection during paving. Make sure the slurry is in full contact with the back of the tile. 12. Retaining the size of the seam According to the size of the tile, a gap of corresponding size is reserved between the brick and the brick to be caulked. The toothpick can be fixed first, and the adhesive has certain adjustability, and the size of the slit can be adjusted. 13. After the horizontal inspection tile is finished, the worker will use a professional measuring instrument to check the flatness of the tile after the paste to ensure the final result is satisfactory to the customer. 14, the finished product protection tile must have protective measures, can be protected with a film. Well, the above is the introduction of the relevant content of the home improvement bathroom tiles. After reading this article, I believe that you have a certain understanding of the home improvement bathroom tiles. If you are doing home improvement and choosing home bathroom tiles, you may wish to refer to the above suggestions. If you want to know more about decoration, please continue to pay attention to the decoration home network. More related wonderful reading: Bathroom tile color matching skills, how to choose bathroom tiles Bathroom tile renovation method bathroom tile renovation considerations How to waterproof bathroom tile joints? Bathroom tile seam waterproofing method Bathroom tile color selection bathroom tile color matching Bathroom tile size introduction bathroom tile size selection Screwdriver Bit,Best Screwdriver Bits,Best Screwdriver Bit Set,Magnetic Screwdriver Bits henan horn tools co.,ltd. , https://www.nbhorntoolsltd.com
