Ultra Plantâ„¢ Grow Light offers One Chip Technology aimed to meet your indoor growing expectation such as improve plants' quality, increase yield, or better the margin, etc., all for helping you realize a higher return on your crops.
From Ultra Plantâ„¢ APP, you are able to schedule the growing process including photoperiod, brightness and spectral in advance. The lighting system will help you grow smarter, easier and better.
Deep Red Grow Light,Deep Red Led Grow Light,Deep Red Led Grow Lights,Deep Red Grow Lights Feton Corporation , https://www.fetongrowlight.com
Innovation through translation gateway <br> <br> translation product installation mounted into even gate lines embedded, fixed pan shutter, three control wiring portion.
1. Pre-embedded lines â— Set the position of the chassis according to the customer's requirements. Choose the best route between the center point of the fixed position of the chassis and the control room, and bury or excavate the cable trench.
â— Put appropriate diameter conduits (PVC pipe or steel pipe) in the dug line trench to penetrate the power line and control line required by the equipment (control lines include: manual button line 3 core, RS485 communication signal line 3 core).
If the distance is far away, the power line and control line must be separately piped (2 pipe distance should be above 50CM).
â— Connect an 8-core machine line between two gates.
â— After all lines are laid, it is best to fill the concrete after successful commissioning.
2. Fixed translating brake â— Firstly, make 2 translating brakes powered, make the wings run to the closed state, then align the two translating brake wings so that the wings are on the same straight line, and the distance between the wings and the wings is 3CM to 5CM.
â— It is necessary to test whether the infrared is aligned, and all the functions are debugged. â— Mark the ground at the center of the screw hole of the base and the edge of the chassis, remove the chassis, and drill the hole vertically with a drill on the screw hole that marks the mark. , size, depth to meet the requirements of the expansion screw equipment will be moved to the original position, into the expansion screw and tighten the screws to power the brakes:
Before power on, you should carefully check the various terminals of the main board of the brake, whether there is looseness, ensure that the mechanical part is not stuck, the operation is flexible, the equipment has been reliably grounded, there is a short circuit phenomenon, etc., and after confirming the correctness, it can be powered on.
3. Transistor brake wiring â— Connect the power cord of the equipment according to the wiring diagram of the transaxle â— If the equipment needs to install other control systems (such as access control system, fingerprint management system, and consumption management system), the output signal line of the control system needs to be connected. The 1 (green), 2 (black), 3 (blue), and 2 (black) terminals of the terminal block are common. â— If you need to use the manual button to control the gate, you can extend the factory-applied small button line.
â— The two panning gates are used synchronously. Please connect the line to the two gates and connect them.
â— Infrared access method. The power supply is connected to 12V. Signals from the right to the left are IR1, IR2, IR3, IR4, and IR5. At least 3 pairs or 3 pairs or more, if 3 pairs will access IR1, IR3, IR5.
â— If two gates are connected, they need to be connected. The connection line is an 8-core line. The access mode is as follows. If there are two AB gates, the 11-connection of the A-line will be B. At the end, the A station 12 is connected to the B station 11 station, the A station 13 is connected to the B station 17 station, the A station 14 is connected to the B station 16 station, the A station 15 is connected to the B station 15 stations, and the A station 16 is connected to the B station 14 station A station 17 terminates B station 13 station A station 18 terminates station B station 18 station, as does many stations. Both gates of a channel are connected in this way. 
Innovations through the transition gate function debugging â— This gate is a two-way normally closed translation gate. External inwards carding signal, outgoing card card signal.
â— When there is no swiping signal, when the pedestrian enters from the entrance to the alarm. Similarly does not swipe the card signal, when the pedestrian from the entrance to the alarm â— Pedestrian brush cartoon line: Wing open start delay, in the set pass time pedestrian pass the wing Closed, if the pedestrian does not pass the time, the wing will be closed. When someone enters in the reverse direction, the gate will be closed immediately and an alarm will be given. When the person or object is in the intermediate anti-clip infrared, the alarm will be issued but the gate will be turned off. Will not close so as to avoid unnecessary harm.
â— If a person is too close to the passage of a pedestrian, the time limit is used as a person.
â— Automatic detection: When the object is obstructed, it will be automatically detected 5 times, and then the blocking position will be stopped. If the signal is given in the same direction, the gate will return to normal. If the switch is not able to find the zero position at the beginning, five tests will be conducted. After five tests, the operation will be stopped to avoid damage to the gate parts;
â— The speed of the sliding gate switch is adjustable. See parameter settings for details.
Ultra Plantâ„¢ Grow Light is combined our advanced All-In-One technology with patented optical design and customized light full spectrum supported from our experienced LED engineers, plant specialists and other partners working on horticulture.
Ultra Plantâ„¢ is the most versatile horticultural grow lighting fixture for indoor plants with flexible full spectrum, brightness control and uniform, wider light distribution, suitable for top lighting of all types of crops. No matter it applies to anywhere for any crop, Ultra Plantâ„¢ can do perfect work for you.
Innovation Pass Translation Gate Installation and Commissioning Instructions
Panning gate is a high-tech product mainly for intelligent management of personnel channels. It is an upgraded product of intelligent three-roll gates and swing gates . This product is used for processing fine work, complete energy, and high grades. It is mainly used in high-grade residential areas, smart buildings, and hotel clubs. And other high-end places. Then, the following is a description of the installation and commissioning of the Innovation Passgate, where the information will allow you to understand the installation and commissioning of the transaxle.